Waste Oil Fired Equipment

Industry's ONLY Non-Carboning Oil Preheater block with Solid State circuit board controller. These items precisely control the oil and air temperatures to insure stable viscosity for optimum control of the flame resulting in a thorough burn. Heater block never carbons or needs to be removed for cleaning. Industry normal annual parts kit not needed with Omni's system! Readjustment of electrodes and nozzle replacement every 5 years is all that is needed due to erosion only.

Why OMNI?

Specifications & Options

Return on Investment Calculator

Typical Installations

Omni is the only waste oil burner manufacturer who can say without equivocation it's oil preheater block absolutely will not carbon the oil internally due to its patented design. Therefore, the industry normal removal of carbon in the preheater block is not necessary. This design ensures that OMNI customers will never need to remove the burner for periodic carbon cleaning! There are many who have easy access to their oil preheater block, but cleaning the hard lava-like carbon is not an easy task! Others request the entire burner be serviced at least annually. Part of that service is flushing their oil preheater block of carbon buildup. Some must do this more than others, as frequently as twice a season. Fully cleaning and removing carbon is a difficult chore. Even after cleaning, carbon chunk particles can remain. Shortly after service, they can plug the oil nozzle, shutting the unit down. This causes a lot of down time and repeat service, not experienced with OMNI units. Additionally, some manufacturers request their customers shut the unit down during the summer months to eliminate the carboning process. This is not necessary if the heater block assembly is an OMNI system. Just leave your unit on and it will automatically start by the thermostat when heat is needed. Omni burners do no need to be torn apart to access the heater block for cleaning. These are a few of the operating procedures COMPETITORS believes are standard; NOT WITH OMNI! OMNI offers five models of boilers: OWB-9 OWB-15 OWB-25 OWB-35 OWB-50

Unique design provides high efficiency. The OMNI cast iron boiler is a revolutionary idea in industrial heating. It utilizes the highly efficient, extremely durable Scotch Marine design principle that has been proven in decades of use in large commercial and industrial heating systems. Boiler is manufactured in Germany, and sections are assembled there as well.

Swing out door allows money saving serviceability. Unlike traditional boilers which require hours of disassembly, the OMNI's hinged front door provides instant access to all of the boilers' heat transfer surfaces. All service and cleaning can be completed literally in minutes, creating additional savings. A clean boiler is a more efficient boiler.

This unique wet base design passes the hot combustion gases three times through the boiler under negative pressure. This maximizes the gases contact with the boiler's water surface area. The result: 84% Efficiency, Burns Clean, Zero Smoke. Our competitor's conventional one-pass design is less efficient and requires time-consuming, cumbersome disassembly of parts for cleaning.

Waste Oil Boilers Standard Equipment

Factory Assembled Cast Iron Sections Refractory Insulated Hinged Front Door With Sight Glass Insulated Jacket ASME Relief Valve 300 PSI Theraltimeter Gauge Draft Inducer (Optional) Boiler Drain High Limit Aquastat Relay Combination (L-8148A) Except Models 35 And 50 Circulator - Except Models 35 And 50 Relay - Models 35 And 50 Only Flow Control Oil Supply Pump Serviceable Oil Filter Pre-built Control Manifold - Models 35 And 50 Only Low Water Cutoff Control Manual Reset High Limit Aquastat Control

Omni's Patented Flame Control System Designed and constructed waste oil burning equipment that reached a level of performance the industry considers unattainable! Our patented complete waste oil burning system with a universal burner mounting flange allows easy retrofit of our burner system to various configuration and sizes of combustion chambers. Initial flame adjustment is all that is needed with complete control thereafter. System Benefits Non-carboning oil heater block - cleaning not required A thorough burn - greatly reducing ash deposit accumulation Only system that can burn straight 90 weight oils Less stress on metals - can't overfire. No target burn-out Clean heater once a season under normal conditions The most reliable, consistent operation Greater efficiency Variably controlled, A/C converted, D/C gear motor driven waste oil pump This Remote flow control pump supplies the exact gallons of oil per hour to each waste oil burning appliance and has the ability to control flame even when various viscosities are used - furnace or stove oil to 90 weight straight - flame remains stable. This rotary style gear waste oil pump is to be located at oil supply tank and is capable of pushing 100's of feet to the used oil firing unit. Other features include: Oil Primer Switch Inline Breaker Oil Pressure Gauge - Bench mark indicator for proper flame length adjustment and filter pump screen or valve cleaning requirements. Cleanable Strainer Oil Filter - removal of one nut for screen access. Oil Shut-Off Valve - eliminates start delays due to possible drain back Adjustable Motor Speed - initial set-up only - once set, no adjustment needed thereafter Patented Oil Preheater & Controller Continues the stabilization of the waste oil viscosity by holding oil and air temperatures that pass through it exact. Resulting in the most thorough and complete burn. OIL HEATER BLOCK WILL NOT BUILD UP CARBON INSIDE ITS OIL PASSAGES!

These charts demonstrate the efficiency and consistency of the Flame Control System Other Waste Oil Burners: Omni Waste Oil Burners with Flame Control: